If orders are placed before 16:30 they will be sent the very same day. On Fridays before 15:00 hours

Product successfully added to your shopping cart


There are 0 items in your cart. There is 1 item in your cart.

Total products
Total shipping  Free shipping!
Continue shopping Proceed to checkout



Quick Overview


If you want to try our GLACE filament to make small pieces, this pack is ideal for you.  ±35 gr per sample. 

  • 1.75mm
  • 2.85 mm
Add to wishlist
Delivery in 24/48 hours*
15 days Return*
180 days Warranty *
Free Shipping from 99€*(península)
If you make your order before 5 P.M we will send it the very same day.

Orders placed before 17:00H will be placed on the following day (working days).

Accessories and related products

We can apply alcohol to Glace to get different results, this way we can get several effects like make completely transparent

workpieces or polish the outside to eliminate rough surfaces and achieve a pearlescent effect. In addition, due to the adherence in
between layers the piece increases its structural strength forming a substantial block and getting strong water tightness.


Please, take into account that to print pieces with great transparency, they must be pieces with one layer only, this way the alcohol can
penetrate homogeneously in the material. If you want to get good mechanical resistance we recommend to use noozles of 0,8mm or
bigger. This way, you will get a wall with the sufficient thickness to keep the desired mechanical resistance.
To get a bigger transparency effect using Glace, we recommend printing using the option “Spiral vase”.
1. Apply treatment with alcohol (ethyl or isopropyl) with a concentration higher than 70°. The higher the alcohol level, the faster the
process, although it is also more difficult to control. The different methods of application are as follow:
• Direct application by immersion:
Submerge the workpiece directly into alcohol, so that it comes in contact with the entire surface. Remove the workpiece and then let it drain so that the
alcohol can evaporate freely. Please, take into account that this method is very aggressive as if the alcohol penetrates deep in the piece, this can be
soften varying the geometry.
• Application by evaporation:
In a closed container, introduce a paper impregnated with alcohol placed around the piece. Then we introduce the piece taking great care that they do
not come into contact. Close the container and allow the evaporation to affect the piece achieving the desired effect.
2. Leave the piece to rest inside the container. Once the piece has been impregnated in alcohol leave it to air dry, depending on the amount
of alcohol absorbed by the piece it can soften a bit, when the alcohol has evaporated completely the piece will return to its normal state.
Following the previous steps, what we achieve is to dissolve the surface layer getting a perfect union in between layers and making a
continuous solid that allows the material to get transparency.


To smooth the workpiece surface, you can apply the previous process to workpieces with any kind of geometry. In this case it is important
to be careful when making an immersion in alcohol because it can get into the filling of the piece affecting the material too much and compromising its integrity.

1. Print a workpiece using Glace.
2. Apply alcohol treatment (ethyl or isopropyl) following the next steps:
• Direct application by immersion.
• Direct application by tools (Pulverized, applied with a brush, etc…)
• Application by evaporation.
3. Leave the workpiece to rest so the alcohol evaporates, excess of alcohol can soften the workpiece too much.
• Glace is a material that degrades with excess temperature, we recommend not to keep it in the extruder for too long to avoid sealing.
• Both ethyl and isopropyl alcohol affect the material in the same way, we recommend using ethyl alcohol for better safety during handling
• Due to the evaporation of alcohol, it is advisable to perform the treatments in a ventilated space using protection measures, mask, glasses, etc.
• Alcohol is flammable and should be kept away from heat sources.

Write a review




If you want to try our GLACE filament to make small pieces, this pack is ideal for you.  ±35 gr per sample. 

xUso de cookies

Utilizamos cookies propias y de terceros para mejorar la experiencia de navegación, y ofrecer contenidos y publicidad de interés.
Al continuar con la navegación entendemos que se acepta nuestra política de cookies.